323412: 模具工人 TOOLMAKER SKILL LEVEL3
| MLTSSL | Medium and Long-term Strategic Skills List |  |
| STSOL | Short-term Skilled Occupation List |  |
| ROL | Regional Occupation List | |
Assessing Authority: TRA
| GENERAL SKILLED VISA 189 | 无资格 |
| State | Capital | Visa subclass 190 | Visa subclass 491 |
| ACT | Australian Capital Territory | Canberra | Yes | Yes |
| NSW | New South Wales | Sydney |
|
|
| NT | Northern Territory | Darwin | Yes | Yes |
| QLD | Queensland(Offshore list) | Brisbane |
|
|
| SA | South Australia | Adelaide | Yes | Yes |
| TAS | Tasmania (Category 1) | Hobart | Yes | Yes |
| VIC | Victoria | Melbourne |
| Yes |
| WA | Western Australia (General stream) | Perth |
|
|
Yes：有资格Occupation may be Eligible
Yes：补充技术清单或特殊情况适用的职业 Occupation in the "Supplementary Skilled List" or "Special Conditions Apply"
Yes：职业不在"State Occupation List"或职业状态为“Closed”，但若满足条件仍有机会申请
？：点击州担保详情查看详情
州担保详情 - ANZSCO 323412
ACCESS LIST |
|
| Status | State/Region | Type Visa | Explanation/Additional Requirements |
|---|
| Closed | New South Wales | Visa subclass 190 |
|
| Open | New South Wales | Visa subclass 491 (regional) |
|
ACCESS LIST |
|
| Status | Explanation |
|---|
Closed | You may be eligible to apply for ACT nomination if you meet the nomination criteria. |
ACCESS LIST |
|
| Status | English Requirements | Comments |
|---|
| Open | Minimum of IELTS 6 in each band or equivalent |
|
This occupation is in the State Occupation List
The State Occupation List is available to all applicants, including international graduates of South Australia. Please review theskilled nomination requirements before applying.
If you are an international graduate of South Australia, you should also review the following page: International graduate occupation and waiver requirements
323412 模具工人职业描述 Job description
制造和修理工具、模具、夹具等精密零件和设备，配合机床等机械设备的 。
Makes and repairs tools, dies, jigs, fixtures and other precision parts and equipment to fine tolerances for machine tools and other production machinery.Previously referred to in ASCO as:4113-11 Toolmaker.4113-01 Toolmakers - Supervisor.
323412 模具工人职位别名
323412 铸模工 Die Caster
323412 制模师 Die Sinker
323412 Jigmaker (Metal)
323412 塑料模具制造商 Plastic Mould Maker
323412 冲压工具制造商 Press-tool Maker
323412 模具工人技术等级 Skill level
模具工人的技能等级为3电信技术员的技能等级为3（ANZSCO Skill Level 3）。
323412 模具工人所属职业列表
澳洲STSOL职业列表Short-term Skilled Occupation List
323412 模具工人澳洲技术移民职业评估 Skills assessment authority
TRA - 澳大利亚职业技术认证中心 Trades Recognition Australia：大陆技术移民申请的绝大部分职业都是通过该类别评估。TRA移民技术评估类别申请的条件为具有澳洲要提名职业相对等的资格（一般是 AQFIII，IV或 Diploma），至少3年的全职提名职业作经验，近2年内至少1年全职带薪提名职业工作经验。对于在获得等同AQF相关资质之前的工作要获得认可的话， 需之前至少5年提名职业或者提名职业相关全职工作经验。
相关职业
323411 工程制模工人 Engineering Patternmaker
3234 工具匠与工程制模师
ANZSCO 3234 工具匠与工程制模师职责概述
• 工具制造工,工程制模师维修工具,模具,钻模,卡具等其他精密仪器,设备.TOOLMAKERS AND ENGINEERING PATTERNMAKERS make and repair tools, dies, jigs, fixtures and other precision parts and equipment to fine tolerances for machine tools and other production machinery, and construct full-size engineering, visual and experimental models and models for the manufacture of prototype developmental products.
ANZSCO 3234 工具匠与工程制模师技能要求 Indicative Skill Level
• 本单元的大多数职位需要具有与下述资质和经验相当的技术层次。Most occupations in this unit group have a level of skill commensurate with the qualifications and experience outlined below
• 在澳洲：AQF证书3级，包括至少2年的在职培训或AQF证书IV级（ANZSCO技术3级）In Australia: AQF Certificate III including at least two years of on-the-job training, or AQF Certificate IV (ANZSCO Skill Level 3)
• 在新西兰：NNZ资格证4级（ANZSCO技术3级）In New Zealand: NZ Register Level 4 qualification (ANZSCO Skill Level 3)
• 至少3年的工作经验可以代替上述的资格证。At least three years of relevant experience may substitute for the formal qualifications listed above.
• 有时除了资格证外，还需要相关的工作经验和/或在职培训。In some instances relevant experience and/or on-the-job training may be required in addition to the formal qualification
ANZSCO 3234 工具匠与工程制模师主要职责 Tasks Include
• 研究图纸,规格以确定物品的规模与尺寸。 studying drawings and specifications to determine dimensions and tolerances of articles to be manufactured and models to be constructed
• 用不同仪表进行测量并对金属原料与铸件进行标记。measuring and marking out metal stock and castings using various gauges
• 使用机床对金属和木材成品进行成形处理。shaping metal and wood stock using machine tools
• 检查成品和 终模型的精度，使用精密测量仪器。checking accuracy of manufactured articles and finished patterns to fine tolerances, using precision measuring instruments
• 测试和修改成品。testing and modifying manufactured articles
• 应用保护涂层，为模型截面上漆。applying protective finishes to patterns and painting pattern sections to indicate method of assembly
• 重组模型截面，对半成品进行成形处理。assembling pattern sections and shaping work pieces to specified finish
• 给模具浇注材料，并分散模具外的材料；制作玻璃纤维织布和塑料树脂的薄片。pouring and spreading materials into moulds and over models of patterns, and building laminations of fibreglass cloth and plastic resin to fabricate patterns
• 修理破损的模型，校正模型以弥补铸件的瑕疵。repairing broken and damaged patterns and correcting patterns to compensate for defects in casting
• 为布局和检查制造模板。constructing templates for layout and inspection
